LED's
-
WHITE LED's 3mm ()Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.30€
-
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers ()24 ultra bright smart LED Ring are arranged in a circle with 66mm outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED.Add to Cart9.52€
-
MAX7219 Dot Led Matrix Module MCU LED Display Control Module Kit For arduino ()MAX7219 is an integrated serial input / output common-cathode display drivers , which connects the microprocessor 7-segment digital LED display with 8 digits , bar graph can also be connected monitor or 64 separate LED. On type B BCD encoder includes an on-chip , multi-channel scanning loop , segment word drive, but also a 8x8 static RAM for storing each data . Only one external register is used to set the segment current for each LED .A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update does not overwrite all of the display . MAX7219 also allows the user to select each of the data code or not coded .The entire device includes a 150μA low-power shutdown mode , analog and digital brightness control , a scan-limit register allows the user to 1-8 bits of data , there is an LED light so that all the detection mode .Requires only three IO ports can drive a dot ! No flashing dot matrix display ! Support cascade !
Single module can drive a common cathode 8 * 8 dot matrixModule Operating voltage : 5VModule size : 5 cm X 3.2 cm wide X 1.5 cm highHoles with four screws , diameter 3mm, can be fixed by using our M3 studsMdules with input and output interfaces , support for cascading multiple modulesaeProduct.getSubject()Is a block left input port, an output port on the right .When control of a single module , simply input port receiving CPUWhen cascading multiple modules 3 , output and input termination CPU, the input output termination module of the first two modules of the first one , the first two modules of terminating the input of the first three modules , and so on . ..To 51 single example:VCC → 5VGND → GNDDIN → P22CS → P21CLK → P20aeProduct.getSubject()1PCS MAX7219 dot matrix module ( finished with lattice , has tested well )5PCS DuPont lineAdd to Cart4.64€ -
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers ()WS2812 NeoPixel Stick Strip 8 Way Serial 5050 RGB LED with Integrated Controllers UK Stock
Ideal for Arduino Projects, works great with Adafruit Neopixel Library
Description:
Control circuit and RGB chip are integrated in single 5050 package.
Each LED has built-in signal reshaping circuit.
Built-in reset circuit and power loss reset circuit.
Each pixel of primary color can achieve 256 brightness display
total 16777216 colors
Scan frequency not less than 400Hz.
Single Data Connection for all LEDs.
Maximum 5metres between LEDs without any extra circuitry.
30fps with 1024 pixels.
Send data at speeds of 800Kbps.
Internal Constant Current Source for consistent colours across all LEDs.Add to Cart5.95€ -
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ( Copy ) ()10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat TubeAdd to Cart4.17€
-
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle ()Item specifics
- Display Type:
- Operating Temperature:
- Accuracy Class:
- Power Supply:
- Measuring Range:
- DIY Supplies:
- Dimensions:
- Model Number:
- Measuring range:
- Input range:
- Display:
- Measurement accuracy:
DESCRIPTION
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle
Measuring range: DC 0.1V-30V
Input range: DC 2.7V-32V
Max Input: DC 32V. The device can be damaged if input is over 32V
Display: Three 0.36 "digital tube
Measurement accuracy: 0.1%
Refresh rate: about 300mS / times
Input impedance: About 100K
Screw holes measures :28mm
Operation Temp: -10 Celsius degree-+65 Celsius degree
Add to Cart4.64€ -
LED breakout module ()This is a breakout board for the WS2812B RGB LED. The WS2812B (or "NeoPixel") is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addressable string.Add to Cart4.17€
-
BLUE LED's 5mm ()Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.36€
-
Red LED's 3mm ()Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.30€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards ()16 ultra bright smart LED are arranged in a circle with 1.75" (44.5mm) outer diameter.The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together!Each LED is addressable as the driver chip is inside the LED.Each one has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim.Power the whole thing with 5VDC (4-7V works) and you're ready to rock.There is a single data line with a very timing-specific protocol.Since the protocol is very sensitive to timing, it requires a real-time microconroller such as an AVR, , PIC, mbed, etc.It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp.As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around.An 8MHz or faster processor is required.Comes as a single ring with 16 individually addressable RGB LEDs assembled and tested.Add to Cart7.14€
-
WHITE LED's 5mm ()Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.36€
-
YELLOW LED's 5mm ()
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.
This is a very basic 5mm LED with a yellow lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA.
Add to Cart0.38€ -
YELLOW LED's 3mm ()
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.
This is a very standard, yellow LED. The lens is 3mm in diameter and it is diffused.
- 2.0-2.4VDC forward drop
- Max current: 20mA
- Suggested using current: 16-18mA
- Luminous Intensity: 40-100mcd
Add to Cart0.30€ -
GREEN LED's 5mm ()Need some really bright LEDs? We are big fans of these clear green LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20degree LED beam. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.38€
-
HIGH POWER DIY 10W 12V 900-1000LM 6000-6500K White Bright LED module chip beads for led lamps ()
Material: Copper + silicone + epoxy resin
Quantity: 1
Emitter Type: LED
Total Emitters: 9
Power: 10 W
Color BIN: White
Rate Voltage: 12 V
Luminous Flux: 900~1000 lm
Color Temperature: 6000~6500 K
Application: Great for DIY project
Packing List: 1 x LED module
Add to Cart2.38€ -
GREEN LED's 3mm ()
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.
This is a very standard green LED. The lens is 3mm in diameter, and is diffused.
- 2.0-2.4 VDC forward drop
- Max current: 20mA
- Suggested using current: 16-18mA
- Luminous Intensity: 40-100mcd
Add to Cart0.30€ -
BLUE LED's 3mm ()Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Add to Cart0.30€
-
Red LED's 5mm ()
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.
This is a very basic 5mm LED with a red lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA.
Add to Cart0.38€