Search
Search Criteria
Products meeting the search criteria
-
12V 37 DC Geared Motor ()Rated voltage: 12V
Speed parameters:
Ordinary model: no load speed 130 RPM (plus or minus 5%), load 7 kg (per cm), 70 rpm, locked rotor torque 20 kg
Gasket type: 6-7 rpm at 12V; 13 rpm at 24 V
Torque: 2.5kg
Reduction ratio: 1:86
Motor diameter: 32.8mm
Motor length: 22mm
Fixed aperture: 3mm (M3 screw)
Reducer diameter: 37mm
Reducer length: ordinary type: 24mm; Gasket size: 25mm
Step height: Ordinary: 6mm; Gasket: 4.5mm
Shaft length: Ordinary: 15mm; Gasket size: 19mm
Motor shaft diameter: 6mm, D-type shaft (pin edge 0.65mm)Add to Cart10.12€ -
L293D WIFI NodeMcu Lua Motor Driver Shield Board For ESP8266 ESP-12E Dual High Power H Bridge Module For Arduino 4.5-36V L293 4W ()Power input:
Motor power supply (VM): 4.5V ~ 36V, can be powered separately
Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately
Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and control
Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H)
Drive part of the work current Io: ≤1.2A
Maximum power dissipation: 4W (T = 90 ℃)
Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V
Working temperature: -25 ℃ ~ + 125 ℃
Drive Type: Dual high-power H-bridge driver
ESP12E Dev Kit Control Port: D1, D3 (A motor); D2, D4 (B motor)
Expand two-way motor-driven, two-way direct drive motor
Onboard power switch
Motor power, control power separation; In the experiment, by short-circuiting block the merger,the VIN and VM short, while power to the motor and the control board
Notice:
When inserted into the ESP-12E module,please note the direction consistent with an expansion board antenna
The use of short modules that can simultaneously control board and motor.Add to Cart6.55€ -
NodeMCU Motor Shield Board L293D for ESP-12E from ESP8266 esp 12E kit diy rc toy wifi rc smart car remote control Node MCU ()- ESP12 DEV KIT development board expansion module;
- lead ESP12 DEV KIT All-function pins: SPI, UART, GPIO, AI and 3.3V power connector;
- expand two-way motor-driven, two-way direct drive motor;
- onboard power switch;
- L293D
- Motor power range: 4.5V ~ 36V;
- Control power range: 4.5V ~ 9V;
- Motor power, control power separation; In the experiment, by short-circuiting block the merger, the VIN and VM short, while power supply to the motor and the control board.
SPECIFICATIONS
- Motor Power (VM): 4.5V ~ 36V, can be a separate power supply;
- Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately;
- Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) simultaneously drive and control the motor;
- Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H);
- Drive part of the work current Io: ≤1.2A;
- Maximum power dissipation: 4W (T = 90 )
- Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V
- Working temperature: -25 ~ + 125
- Drive Type: Dual high-power H-bridge driver
- ESP12E Dev Kit Control Port: D1, D3 (A motor); D2, D4 (B motor)
- Module Weight: about 20g
Add to Cart4.64€ -
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle ()Item specifics- Display Type:
- Operating Temperature:
- Accuracy Class:
- Power Supply:
- Measuring Range:
- DIY Supplies:
- Dimensions:
- Model Number:
- Measuring range:
- Input range:
- Display:
- Measurement accuracy:
DESCRIPTION
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle
Measuring range: DC 0.1V-30V
Input range: DC 2.7V-32V
Max Input: DC 32V. The device can be damaged if input is over 32V
Display: Three 0.36 "digital tube
Measurement accuracy: 0.1%
Refresh rate: about 300mS / times
Input impedance: About 100K
Screw holes measures :28mm
Operation Temp: -10 Celsius degree-+65 Celsius degree
Add to Cart4.64€ -
L9110S DC Stepper Motor Driver Board H Bridge L9110 for arduino ()L9110S DC Stepper Motor Driver Board H Bridge FZ0537
Description:
Low quiescent current
Wide supply voltage range: 2.5V-12V
800mA per channel continuous power output capability
Lower saturation voltage
TTL / CMOS compatible output level can be directly connected to CPU
Output built-in clamp diodes for inductive load
Control and drive integrated into a single IC
With pin high-voltage protection
Operating temperature :0-80
Onboard 2 L9110S motor control chip
Module can drive two DC motors or a 4-wire two-phase stepper motor
Package Included:
5 X L9110S Motor Driver
Add to Cart4.17€ -
Motor-driven expansion board L293D motor control shield For arduino ()
L293D is a monolithic integrated, high voltage, high current, 4-channel driver. Basically this means using this chip you can use DC motors and power supplies of up to 25 Volts, that"s some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what"s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. Features : 2 interface for 5V Servo connected to the Arduino"s high-resolution dedicated timer - no jitter. Can drive 4 DC motors or 2 stepper motors or 2 Servo. Up to 4 bi-directional DC motors with individual 8-bit speed selection. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 25V DC. Pull down resistors keep motors disabled during power-up. 2 external terminal power interface, for separate logic/motor supplies. Tested compatible for Arduino Mega, Diecimila and Duemilanove.L9110S DC Stepper Motor Driver Board H Bridge FZ0537
Description:
Low quiescent current
Wide supply voltage range: 2.5V-12V
800mA per channel continuous power output capability
Lower saturation voltage
TTL / CMOS compatible output level can be directly connected to CPU
Output built-in clamp diodes for inductive load
Control and drive integrated into a single IC
With pin high-voltage protection
Operating temperature :0-80
Onboard 2 L9110S motor control chip
Module can drive two DC motors or a 4-wire two-phase stepper motor
Package Included:
5 X L9110S Motor Driver
Add to Cart7.13€ -
MG90S 9g Servo Motor ()Dimension : 22.8mm x 12.2mm x 28.5mm
Stall Torque : 1.8kg/cm(4.8V )2.2kg/cm(6V)
Temperature Range : 0 degree to 55 degree
Operating Speed : 0.1sec/60degree(4.8v),
0.08sec/60degree(6v)
Dead Band Width : 5 usec
Operation Voltage : 4.8 - 6Volts
Motor Type : coreless motor
Gear Type : All Metal gear
Connector Wire Length : 175mAdd to Cart4.17€ -
5V 28BYJ-48 Stepper Motor + ULN2003 Controller Board ()• ULN2003 Driver Board：
A, B, C, D four-phase LED indicates the status of the stepper motor work.
Drive Board Size: 2.8cm x 2.8cm x 2cm
Stepper motor with a standard interface, when used directly plug gable.
FZ0107-28BYJ-48 stepper motor 5v
28BYJ-48 Stepper Motor：
Phase: 4
Type: Hybrid
Holding Torque: 1 / 64
Current / Phase: 5V
Diameter: 28mm
Step angle: 5.625 x 1 / 64
Reduction ratio: 1 / 64Add to Cart4.33€ -
MG996R High Speed Torque Servo Motor For Smart Car ()Model: Towerpro Servos MG996R Dead Band: 0.050 ms Control System: Pulse Width Control Working Frequence: 20ms period / 50hz (Digital Control) (RX) Required Pulse: 3.0 ~ 5 Volt Peak to Peak Square Wave Operating Voltage: 4.8 ~ 6 V DC Volts Operating Temperature Range: 0 to + 55 Degree C Operating Speed (4.8v): 0.200 sec/60° degrees at no load Operating Speed (6v) 0.160 sec/60° degrees at no load Stall Torque (4.8v): 9.4kg/cm Stall Torque (6v): 11kg/cm Motor Type: Brushed Motor Potentiometer Drive: Direct Drive Bearing Type: Output Bearing Gear Type: Brass & Aluminum Gears Case Material: Plastic Programmable: NO Connector Wire Length: 32.0cm (12.6 inch) Dimensions: 40.7×19.7×42.9mm Weight: 55 grams (2.64 oz) Add to Cart6.55€