Latest Products
-
KY-008 Laser Transmitter Durable
4.76€ -
:MOVE mat line following and activity maps - A1 s
8.93€ -
:MOVE mini MK2 buggy kit (excl micro:bit)
50.58€ -
Micro:Bit V2
29.75€ -
Rock 4 SE
136.85€ -
BANANA-PI-M5
140.42€ -
BANANA-PI-ZERO
45.22€ -
120pcs/Box M3 Stainless Steel Screw Nut Brass Column Kit
5.36€ -
Microbit GPIO Expansion Board Educational Shield
7.02€ -
3.7V to 5V 2A 18650 Step-up Battery Module
5.36€ -
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC Step Up Module 5V
2.62€ -
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC Step Up Module 3.3V
2.62€ -
DC-DC Step Up Circuit Module 3V to 5V 1A
2.62€ -
DC-DC Automatic Buck Boost Power Module Step Up and Down Board Input 3-15V Output 5V
5.36€ -
BLE5.0 Bluetooth Module
4.17€ -
GY-NEO-6MV2 GPS Module
5.36€ -
Multi-Function ProtoShield Expansion Board
8.93€ -
ESP32-CAMERA OV2640
10.12€ -
MG996R High Speed Torque Servo Motor For Smart Car
6.55€ -
MQ Series Gas Detection Module MQ-9
2.98€ -
MQ Series Gas Detection Module MQ-5
2.98€ -
MQ Series Gas Detection Module MQ-135
2.98€ -
MQ Series Gas Detection Module MQ-2
2.98€ -
MQ Series Gas Detection Module MQ-3
2.98€ -
5V ESP8266 2 Channel WiFi Relay Module
7.74€ -
1602A LCD Screen with IIC/I2C
4.52€ -
Raspberry Pi Heat Sink 3pcs
2.68€ -
Aluminum Heatsink Cooler 14 x 14 x 6mm Adhesive Kit for Cooling Raspberry Pi ( Copy )
1.49€ -
Aluminum Heatsink Cooler 10 x 14 x 6mm Adhesive Kit for Cooling Raspberry Pi
1.49€ -
12 Values 60pcs 3296W Trimmer Potentiometer
0.48€ -
TP4056 1A 5V Lithium Battery 18650 Charging Board Module Plates USB type-C
2.96€ -
2WD Smart Robot Car Chassis Kit - PURPLE
17.85€ -
2WD Smart Robot Car Chassis Kit - RED
17.85€ -
2WD Smart Robot Car Chassis Kit - BLUE
17.85€ -
MG90S 9g Servo Motor
2.98€ -
5V 28BYJ-48 Stepper Motor + ULN2003 Controller Board
4.33€
Specifications:
Dimension: 12 x 12mm
Working Voltage: DC 2-5V
Timing can be set to a minimum to a maximum of 2 seconds 1,000 hours
Function and Design
1. The circuit according to claim connected and set a good time resistance and supply voltage;
2. Before the power not trigger output is high;
3. Trigger terminal "falling" trigger effective immediately
after the trigger output terminal goes low at the same time start the timer circuit;
4. Set the timer time to recover after the output terminal is high, wait for the next "falling" trigger;
5. The chip is not repeated triggered, meaning that
continue to trigger in the period after the trigger chip output low if the trigger is invalid;
6. The trigger end of "falling" Trigger refers to the instantaneous change from high level to a low level;
7. General refers to VCC high voltage, low means 0-0.3v or GND,
provided that they meet the level requirements can be;
8. trigger terminal can be connected to touch switch or microcontroller IO port or
other digital circuits have a "falling" can effectively trigger;
9. The trigger can be designed to power, only to trigger a short circuit to ground, power is triggered,
the time to recover after the output to a high level, waiting for the next
Falling edge trigger again.
Chip Features:
1. The use of low-power CMOS technology, lead-free and environmentally friendly.
2. Direct Push can output low LED
(please add current limiting resistor), the output high may push transistor (please add current limiting resistor).
3. Available resistance adjusting timing, there are 8 * N (N = 0.1.2.3) times the timing selection,time can be adjusted from 2s-1000h.
4. Optional trigger timing and triggering termination ground electric timer.
5. standby output high, falling edge trigger, post-trigger output low, after the delay recovery high.
Dimension: 12 x 12mm
Working Voltage: DC 2-5V
Timing can be set to a minimum to a maximum of 2 seconds 1,000 hours
Function and Design
1. The circuit according to claim connected and set a good time resistance and supply voltage;
2. Before the power not trigger output is high;
3. Trigger terminal "falling" trigger effective immediately
after the trigger output terminal goes low at the same time start the timer circuit;
4. Set the timer time to recover after the output terminal is high, wait for the next "falling" trigger;
5. The chip is not repeated triggered, meaning that
continue to trigger in the period after the trigger chip output low if the trigger is invalid;
6. The trigger end of "falling" Trigger refers to the instantaneous change from high level to a low level;
7. General refers to VCC high voltage, low means 0-0.3v or GND,
provided that they meet the level requirements can be;
8. trigger terminal can be connected to touch switch or microcontroller IO port or
other digital circuits have a "falling" can effectively trigger;
9. The trigger can be designed to power, only to trigger a short circuit to ground, power is triggered,
the time to recover after the output to a high level, waiting for the next
Falling edge trigger again.
Chip Features:
1. The use of low-power CMOS technology, lead-free and environmentally friendly.
2. Direct Push can output low LED
(please add current limiting resistor), the output high may push transistor (please add current limiting resistor).
3. Available resistance adjusting timing, there are 8 * N (N = 0.1.2.3) times the timing selection,time can be adjusted from 2s-1000h.
4. Optional trigger timing and triggering termination ground electric timer.
5. standby output high, falling edge trigger, post-trigger output low, after the delay recovery high.
- Availability: 10